Iscar Releases A Brand New Line Of Slitting Cutters Applying Tang-Grip Technology And The Strength Of Sumo Tec Grades

Iscar right now offers a family of high-performance slitting tools that join the convenience and security of Tang-Grip clamping with the increased sturdiness of the brand new Sumo Tec insert grades.

The idea, already verified effective in Tang-Grip parting tools, has now been spread to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets with a specific hand tool, and are clutched tightly in place without having the need for clamps, upper jaws or set screws that can weaken the insert and block chip flow. The pocket composition utilizes cutting forces to retain the insert seated securely in position, removing any prospect of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus increased pocket and insert life.

Iscar's Sumo Tec insert grades feature a distinct post-coating treatment which extensively increases tool life and reliability.

Launched in late 2007, the completely new Sumo Tec treatment flattens the insert's coated surface to eradicate microscopic stress raisers, reduce heat and friction and boost chip flow. The result is enhanced toughness and opposition to chipping and built-up edge, all leading to longer tool lifespan. The golden-colored side on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, allowing higher feed rates.

Their higher rigidity leads to straighter, better accurate cuts and reduced vibration even in large-diameter cutters. The revolutionary Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same variety of inserts as Tang-Grip parting tools. Several other sizes will be added.

Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, delivering remarkable resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.

IC830, supplying extra toughness for heavier parting & grooving including interrupted cuts. It is suited for any stainless steel and high temperature alloys.

IC908, a hard, fine-grain substrate with remarkable chipping resistance, mixed with a brand new Sumo Tec TiAlN PVD coating. It is perfect for nodular or gray cast iron.

IC928 and 928A, PVD TiAlN-coated tough grades fitting for stainless steel, high temperature alloys and other alloy steels. These grades are additionally suggested for interrupted cuts and heavy operations.

Each Tangslit and Tang-Grip inserts are presented in J- or C-type chipformer geometries from Iscar.

Iscar Adds Their Latest Innovations To A Long Line Of Effective Hole Making Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.

A Couple Of Advancements In Carbide Inserts From Iscar From Over The Years
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.

A Number Of Improvements Have Broadened Iscar's Families Of Indexable Endmills For Expanded Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.

New Cutters And Carbide Insert Arrangements From Iscar To Better Maximize The Machining Procedure
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.

Brand New End Mills From Iscar Can Enhance Productivity While Decreasing Costs
Manufacturers and die & mold shops can banish chatter problems in numerous milling operations with Iscar's new Chatterfree end mills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the primary source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.

Commercial Water Heater - Considering All Of Your Needs - Study With Care To Know More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.

What Exactly Vehicle Engineering Careers Do.
Automotive engineers who have years of experience in the automotive industry have the ability and skills of overseeing new projects and product development.